Press nuts, weld nuts, rivet nuts

    Purchased hardware and fasteners

    Press nuts, weld nuts, rivet nuts and screws often sit as separate solids in the STEP assembly. Glintify recognises them by their designation, checks that the geometry matches the type and keeps them out of cutting, bending and welding. Instead they are priced as purchase plus fitting method with your times and rates. If a price or method is missing, the direct price stops instead of becoming zero. Recognition requires a metric designation in the STEP name.

    // Detection

    What Glintify detects

    The system analyzes the part's geometry and extracts every manufacturing-relevant feature without manual input.

    Extracted data

    Designation in the STEP name, shank diameter, length, hole in the host part, position in the assembly, quantity per designation

    // Automation

    What is calculated automatically

    All measurements are extracted directly from the geometry.

    PEM-type press nuts, press studs and standoffs (S, CLS, FH, SO and more) by designation
    Weld nuts to ISO 21670, DIN 928 and DIN 929, weld studs to ISO 13918
    Blind rivet nuts plus standard screws, nuts, washers, pins and retaining rings
    Geometric plausibility check: shank, length and hole match the type
    Host part: verified in hole, in contact, unclear or missing
    Quantity per designation in the assembly, with weight in the calculation
    // Quality

    Quality rules

    The system automatically checks whether the part fits within your capacity and flags designs that can cause production issues.

    A designation missing from the price list gives the status Price missing and blocks the direct price
    A type without a chosen method gives the status Method missing and the line goes to the estimator
    If the CAD quantity changes after a saved quote, the group is marked Review
    An unknown designation only gives a hint of likely purchased hardware, never a price
    Purchased hardware never becomes a weld seam or a manufactured part
    // Setup

    Typical setup

    What a typical setup looks like for this operation.

    The estimator checks the type in 3D with Show in 3D and switches to Treat as manufactured if needed
    The admin sets up methods, times and the price list once per company
    An all-inclusive unit price for simple cases, method plus purchase when the time should be visible
    Material supplied by the customer is marked Supplied by customer
    // Example

    Cost example

    Line-by-line breakdown of the part cost using your machine data and prices.

    Cost itemAmount
    4 × press nut M6, purchaseSEK 6.00
    Pressing 4 × 4 sSEK 1.10
    2 × weld nut M8, purchaseSEK 3.20
    Projection welding 2 pcsSEK 2.40
    Purchased hardware per assembly, illustrative exampleSEK 12.70
    // Costing in Monitor's format

    The same routing line as in Monitor

    On top of our time-based calculation, purchased hardware and fasteners is also costed as a routing line ("beredningsrad") in Monitor's format: production group (work center), setup time, cycle time, allowance (F-time) and piece time, priced with the production group's cost factors. The line can be exported as an article with routing straight to your ERP system.

    Routing lineExplanation
    Production groupFetched from your ERP system or created from the machine park
    Setup timePer batch, not per piece — spread over the quantity
    Cycle timeThe technical time per piece, calculated from the geometry
    F-time %Allowance on top of the cycle time
    Piece timeCycle time × (1 + F-time %)
    Cost factorsMachine, wages + social charges and fixed manufacturing overhead in SEK/h, with a staffing factor
    Cost = setup time × rate + piece time × rate × quantity

    Markups for MO (material overhead), LO (subcontracting overhead), AFFO (general overhead) and profit are added at quote level — exactly as in Monitor's pre-calculation.

    Calculate your own part

    Upload a STEP file, we run the analysis and show exactly what the system detects for purchased hardware and fasteners. No manuals, no calls.